Forse netvoeding bouwen

Alles wat u in andere catogorieen niet kwijt kan en betrekking heeft op modelbouw kan u hier plaatsen.
Plaats reactie
Gebruikersavatar
aad
Berichten: 1525
Lid geworden op: 10 mar 2010, 21:06
Locatie: Maasland
Contacteer:

Forse netvoeding bouwen

Bericht door aad »

De moderne accu laders worden steeds krachtiger.
Zo als ik zelf al heb ondervonden zijn sommige netvoedingen er niet tegen bestand om ze langdurig voor meer als 95% te belasten. Mijn 2 voedingen van 13,8V/20A gingen binnen een half jaar kapot.

Zonder goede voeding heb je niets aan een acculader. Tijd dus om eens op zoek te gaan naar een geschikte netvoeding.
voeding

Wat verwacht ik allemaal van een voeding ?


- Krachtig (op zijn minst 20A continue. Liefst 40A.
- uitgangs spanning 24V ~ 26V.
- Betaalbaar (onder de € 150,-)
- Hoog rendement (weinig warmte ontwikkeling).
- lange levensduur.

Afbeelding

Na wat zoeken op internet bleek dat er mensen waren die met succes een bepaald type computer voeding gebruiken.

Het gaat hier om een voeding van een HP Proliant DL380 G4 server. (series 135). Deze voeding levert een formidable 575W.
De 12V uitgang kan 47A continue leveren .

Na wat zoekwerk op diverse sites die 2e hands goederen verkopen heb ik er twee aangeschaft.

Goedkoop waren ze zeker. Ik heb er 19,95 ex BTW. per stuk voor betaald.
Ze zijn gebruikt, maar ze zien er als nieuw uit.

In tegenstelling tot een gewone PC voeding hoef je bij deze voeding niet de +5V fors te belasten om ervoor te zorgen dat de voeding blijft werken. Simpel 3 pinnen op de connector doorverbinden is voldoende.

Afbeelding

Eerst maar eens voorzichtig beginnen om te kijken hoe deze voeding zich houdt.

Het kleine ventilatortje maakt flink toeren en is zeker niet de stilste. Opvallend is de zeer geringe hoeveelheid warmte die deze voeding produceert.

Zelfs bij een uitgangsstroom van 44A komt er weinig warmte uit de voeding. Ook de uitgangsspanning varieert heel erg weinig. Er zit nog geen 0,1 volt verschil tussen onbelast en belast met 44A.

Afbeelding

Het maximale vermogen wat deze lader kan laden met een ingangsspanning van 12,5V

Twee 6S LIPO-pakketen worden dan geladen met een stroom van iets meer als 9A.

Dit gaat al lekker vlot.

De lader komt echter pas echt tot zijn recht als er een ingangsspanning van 24V ~ 28V beschikbaar is.

De volgende stap is dan ook om een 2e voeding in serie te zetten om zo een module te maken die 24V/47A kan leveren.

Afbeelding
kapot maken is niet moeilijk, heel houden veel moeilijker.
foto archief: http://www.ajvde.nl
Gebruikersavatar
aad
Berichten: 1525
Lid geworden op: 10 mar 2010, 21:06
Locatie: Maasland
Contacteer:

Re: Forse netvoeding bouwen

Bericht door aad »

Om twee van deze voedingen in serie te kunnen zetten moet er één voeding worden aangepast.
De aarde en de massa zitten namelijk met elkaar doorverbonden.

Na een flinke zoektocht in de voeding bleek het niet eenvoedig om de massa los te maken van de aarde. Dus dan maar andersom: we maken de aarde los van de massa.

Dit kan eenvoudig door de aarde draad van de voedings connector af te knippen. Verder moet de afscherming onder de voedings connector worden verwijderd.
Deze afscherming had ik in eerste instantie over het hoofd gezien. Het resultaat was een kortsluiting in de 2e voeding.
Gelukkig is de voeding kortsluit vast. Na de afscherming verwijderd te hebben werkte het perfect.

Afbeelding

Het enige waar je even rekening mee moet houden is dat je een vaste doorverbinding tussen de twee voedingen moet maken.

Deze zorgt ervoor dat de behuizing van de ongeaarde voeding niet onder een te hoge spanning komt te staan.

Verder moet je ervoor zorgen dat de behuizingen van de voedingen niet tegen elkaar komen.
Dit heb ik opgelost door er 4 lagen duckttape tussen te plakken.

Afbeelding

Het eind resultaat:

Afbeelding

aad.
Laatst gewijzigd door aad op 05 jun 2012, 20:42, 1 keer totaal gewijzigd.
kapot maken is niet moeilijk, heel houden veel moeilijker.
foto archief: http://www.ajvde.nl
Gebruikersavatar
aad
Berichten: 1525
Lid geworden op: 10 mar 2010, 21:06
Locatie: Maasland
Contacteer:

Re: Forse netvoeding bouwen

Bericht door aad »

De beschrijving hoe je deze voeding ombouwt kun je vinden op:

https://sites.google.com/site/tjinguyte ... ects/HP47A

aad.
kapot maken is niet moeilijk, heel houden veel moeilijker.
foto archief: http://www.ajvde.nl
Gebruikersavatar
aad
Berichten: 1525
Lid geworden op: 10 mar 2010, 21:06
Locatie: Maasland
Contacteer:

Re: Forse netvoeding bouwen

Bericht door aad »

Ik heb nog een stukje gevonden op het internet.
Hier worden nog wat bruikbare voedingen beschreven.


Thought it might be useful to gather this in the one place.
The practice of converting computer SERVER power supplies to make a very high quality high power supply at low cost is attractive. It doesn’t normally require any modification to the supply but the hard part is figuring out how to trick them into turning on. Far and away the best way is to find someone who has already done it. I have put down a few references I know about and welcome additions.

This is about SERVER supplies which often have large 12V capacity and not much else; it is NOT about converting normal PC power supplies. (The ‘ground the green wire and add a load resistor’ stuff). That is covered extensively elsewhere.
UPDATE There are now available supplies for PCs that have substantial 12V rails and large (850-1200 Watt) capacity that work without any electrical conversion. If you have used one of these, suggest you start a separate thread.

Please, please. This is a REFERENCE thread. Just post a link (with comments) to other posts that show how to do it if you know of one that isn’t here.

IF YOU HAVE AN OPINION OR JUST WANT TO COMMENT OR HAVE A QUESTION ABOUT CONVERTING A PARTICULAR SUPPLY please do it somewhere else (like the original threads for example or PM me). Obviously info on sources of supply for these devices is welcome though – please post that if you know it, as well as any errors that need correcting.

Bottom Line: If you have an unknown supply you need help with, try a post in the original 12v 100A supply thread (link 2 below) which seems to have a good range of posters - or start a new one with a specific title that includes your question. That thread now has some good info on how to solve an unknown supply as well. See the first few posts. When/if you ever get it to work, then post the link to that info here to make it easier for others to find.

If you have an unknown supply and can't find the information from someone who has already solved it then this post contains the best information/links on how to establish which pins might turn it on and control the output voltage.

http://www.rcgroups.com/forums/showp...87&postcount=7


Hope this proves useful.
John

Various threads containing information on converting different supplies.


1) The original IBM Series 235 Supply which started it all.
http://www.rcgroups.com/forums/showp...33&postcount=3


2) A simple high quality 12Volt 100Amp Power Supply thread starts here
http://www.rcgroups.com/forums/showp...97&postcount=1

This is my thread on the HP PROLIANT DL580/ML570G3 which is a 12V 1300Watt supply. It's still my favourite for quality, power, small size and having a proper plug for the power cord BUT it's extremely noisy because of the two small high speed cooling fans. Most people will find its vacuum cleaner impression a PIA. Note that you have to take care to identify exactly which supply by the part number. There is a range of DL580 computers with different supplies.

3) The Compaq HP ESP114 Series 12V 55A Power Supply thread starts here
http://www.rcgroups.com/forums/showp...73&postcount=1

This is earlb's thread on converting these. Was popular popular and remains a good solution. Decent power but much quieter because they are bigger. Easier to obtain and cheaper as well
The attached picture shows the HP 1300 Watt and ESP114 side by side (thanks earlb). The SMALLER one is the more powerful 1300W supply.

4) Dell A570P-00 570W
http://www.rcgroups.com/forums/showp...&postcount=130

5) Compaq Proliant 169286-002 750W
http://www.rcgroups.com/forums/showp...&postcount=128 plus
http://www.rcgroups.com/forums/showp...&postcount=141

6) Sony APS-111 12V 33.3A (Used in CISCO gear). Also known as Ascom Energy Systems Galaxy D0009237
http://www.rcgroups.com/forums/showthread.php?t=800379


7) HP Power Supply DPS-600PB/700CB
http://www.rcgroups.com/forums/showp...&postcount=253

8) hp PS-3381-1C1 PSU
http://www.rcgroups.com/forums/showt...=358340&page=2

9) My current recommendation is the HP model DPS-600PB series ESP135 PS that is used in ProLiant DL380 G4 Rack Servers. It is rated at 575W, or 47A at 12V. It is compact, quiet and powerful and is easily modified to slow the fan down and isolate the DC out to make a 24V supply from two of them (see below under using two supplies). There is a detailed how-to on T Jin Tech's page here https://sites.google.com/site/tjingu...projects/HP47A and feathermerchant has them as single or dual (24V) supplies. Akshu's thread (#11 below) on a kit to convert two supplies to 24V uses these ones. They are in the bottom left hand picture below.

Using two supplies in series to get 15 or 24V at high power.

Two of the DL580/ML570G3 supplies for example will supply 2600W at 24V on a 240V supply! Here’s the thread I started on the practice of connecting two supplies in series to get 24 Volts at high current. Becoming more relevant with the growth of 1000Watt chargers. Feathermerchant on the forums sells these already made up if you don't feel you have the knowledge to do it yourself.

WARNING

These supplies were never designed to be run in series. Here's a quote from someone who knows what he is talking about. Now we know much more about the internals of these supplies, the DC isolation method (see below) is preferable if you know what you are doing.

I must admit, I am more than a little concerned these days about folks connecting different power supplies in series without a full understanding of the dangers. High powered chargers demand more power, and to get it many people having heard of this practice are haphazardly connecting power supplies in configurations for which they were not designed for and have not been tested or CE certified.

All we can do is fight the good fight and continue to educate people. Every week now I get a call or two with a story about series connecting two random, disparate power supplies in an attempt to get more power - with varying success. I sincerely hope the chances of disaster are infinitesimally small and that most all modern supplies have adequate protection built in to avoid anything catastrophic. My concern is for the people playing around modified industrial or hobby grade equipment who don't understand the physics involved and that their actions may be potentially dangerous.

10) Using two power supplies for higher voltage/capacity chargers: safety issues
http://www.rcgroups.com/forums/showpost ... ostcount=1
See post 183 in particular for conclusions.
kapot maken is niet moeilijk, heel houden veel moeilijker.
foto archief: http://www.ajvde.nl
Gebruikersavatar
aad
Berichten: 1525
Lid geworden op: 10 mar 2010, 21:06
Locatie: Maasland
Contacteer:

Re: Forse netvoeding bouwen

Bericht door aad »

Hallo allemaal,

hier nog even een aanvulling.
Er staat ook in beschreven hoe je bij sommige typen de ventilator snelheid kunt instellen.

Server modifications

aad.
kapot maken is niet moeilijk, heel houden veel moeilijker.
foto archief: http://www.ajvde.nl
Gebruikersavatar
aad
Berichten: 1525
Lid geworden op: 10 mar 2010, 21:06
Locatie: Maasland
Contacteer:

Re: Forse netvoeding bouwen

Bericht door aad »

Eigenlijk hoort het niet helemaal thuis in dit draadje.
Maar het is misschien wel logisch om het hier maar te plaatsen.

Met het gratis te downloaden programma Logview wat te vinden is op http://www.logview.info kan je gebruiken in combinatie met een heleboel
laders om het laadproces van je accu's zichtbaar te maken.
onder meer de robbe laders: Powerpeak B6EQ, Powerpeak II, Powerpeak III, Powerpeak IV, Powerpeak Twin 1000 worden ondersteund.

Afbeelding

als voorbeeld hier onder een 3S lipo van 2600mAh, welke geladen wordt in "Store mode".
(In Store mode wordt geladen tot 60%.)

Afbeelding

Duidelijk kan je zien dat de lader het laadproces regelmatig even stopt om te meten hoe vol de accu is.

aad.
Laatst gewijzigd door aad op 17 okt 2012, 19:11, 2 keer totaal gewijzigd.
kapot maken is niet moeilijk, heel houden veel moeilijker.
foto archief: http://www.ajvde.nl
Gebruikersavatar
aad
Berichten: 1525
Lid geworden op: 10 mar 2010, 21:06
Locatie: Maasland
Contacteer:

Re: Forse netvoeding bouwen

Bericht door aad »

Bij deze even een fotoreportage van het ombouwen van een voeding van een HP DL380 G4 server. (575 Watt, 12,5V/47A).

Afbeelding
De zijkant er af halen.

Afbeelding
De bovenkant er af

Afbeelding
De connector aan de achterzijde los maken om bij de schroeven te komen die er uit moeten.

Afbeelding
Deze afstandsbussen uitboren.

Afbeelding
De verwijderde bussen.

Afbeelding
Beveiliging verwijderen.

Afbeelding
Uitgeboord.

Afbeelding
De juiste doorverbindingen om de voeding te laten werken.

Afbeelding
De stekkerbussen afzagen zodat er meer schroefdraad overblijft.

Afbeelding
De afgezaagde stekkerbussen.

Afbeelding


Afbeelding
Vertinnen van de aansluitingen.

Afbeelding


Afbeelding
En zo worden ze er tussen gesoldeerd.

Afbeelding
Ook de tweede bus gesoldeerd.

Afbeelding
Weer een setje voedingen klaar voor een tweede leven.

Afbeelding
In serie gezet levert dit een keurige 25,31 volt op bij 47A.

Afbeelding
En zo wordt het aangesloten.
kapot maken is niet moeilijk, heel houden veel moeilijker.
foto archief: http://www.ajvde.nl
Plaats reactie